Smiths Tachometer Retrofit Board – Case 2401/01 (STR-2401-N7)
Couldn't load pickup availability
Pre-order: early-bird price for the first 20 boards. Ships by January 4, 2027.
You're charged today. Cancel any time before your board ships for a full refund. Each board is assembled, tested and pre-calibrated in the USA and covered by a 1-year limited warranty.
Pictures are 3D renders of the board; photos of the production board will replace them when the first batch is built.
Bring a dead or erratic Smiths tachometer back to life without replacing the gauge. The STR-2401-N7 replaces the original electronics inside case 2401/01 and drives the original Smiths movement, so your dial, needle and dashboard stay exactly as they were.
Will it fit my car?
- ✅ Smiths electronic tachometer, case 2401/01
- ✅ Negative-earth vehicles
- ✅ 4- or 6-cylinder 4-stroke engines, dials up to 7000 RPM
- ✅ Signal from the coil CB (−) terminal, a CDI tach wire, or an ECU square-wave tach output (6 V or more)
- ❌ Not for positive-earth cars, 8-cylinder engines or 8000 RPM dials. Positive-earth and 8-cylinder versions are planned: email us to hear when they are ready.
- ❌ Open-collector ECU outputs need an external pull-up resistor to +12 V.
Not sure? Email support@cranktrace.com with your case number and engine before ordering.
Why it's built this way
- Fully analog, no firmware: each ignition pulse sends one fixed-width pulse to the movement, the same principle as the original.
- Shipped pre-calibrated: every board is bench-tested and calibrated before it ships. The included instructions explain how to fine-tune it to your gauge if needed.
- Protected for automotive use: a resettable fuse, reverse-polarity protection, and transient clamps on the supply and the signal input.
- Easy to diagnose: a green LED shows power, and a second LED flickers with every ignition pulse.
- Supported by the engineer who designed it.
In the box
- STR-2401-N7 retrofit board, pre-calibrated
- Info card with your board's serial number and warranty terms
- Installation instructions, including the calibration procedure
Specifications
- Supply: ignition-switched +12 V (stays regulated down to about 11 V)
- Signal needed: tach pulses must reach at least about 6 V
- Range: 4- or 6-cylinder engines, up to 7000 RPM
- Calibration: span trimmer (VR1); zero is mechanical
- Assembled in the USA
Technical overview
How each stage of the board works, the fit limits, calibration and the bench test every board passes: download the STR-2401-N7 technical overview (PDF).
Smiths is a trademark of its respective owner. CrankTrace Electronics is not affiliated with or endorsed by Smiths.
Ships by January 4, 2027. Boards are built, tested and calibrated in December and ship in order-number order.
You are charged today. Cancel any time before your board ships for a full refund: just email support@cranktrace.com.
If the date moves, we email you before January 4 with the new date and the choice to cancel for a full refund.
Early-bird price: $89 for the first 20 boards, until December 31, 2026. The regular price is $99.
How do I know my tachometer is a case 2401/01?
Check the case number on your Smiths tachometer. If you are not sure, email a photo of the back of the gauge and your car's make, year and engine to support@cranktrace.com before ordering.
My car is positive earth. Will it work?
No. This board is for negative-earth cars only (original or converted). A positive-earth version is planned; email support@cranktrace.com to hear when it is ready.
Does it work with electronic ignition?
Yes. It works with points, electronic ignition modules, CDI tach wires and ECU tach outputs of 6 V or more. Open-collector ECU outputs need a pull-up resistor to +12 V.
I have an RVI gauge with a loop of wire on the back. Can I use it?
Yes, if it is a case 2401/01. The board senses the voltage on the coil (−) terminal, like the later RVC gauges, so the old pickup loop is no longer used.
How is it wired?
Three connections: ignition-switched +12 V, earth, and a sense wire to the coil (−) terminal. The board fits inside the original case and drives the original Smiths movement. Installation instructions are in the box.
Do I need to calibrate it?
No. Every board is bench-tested and calibrated before it ships. One trimmer lets you fine-tune it to your gauge; the instructions explain how.
Does it fit 8-cylinder engines or 8000 RPM dials?
No. It is for 4- or 6-cylinder engines and dials up to 7000 RPM. An 8-cylinder version is planned; email support@cranktrace.com to hear when it is ready.
What if it fails?
It is covered by a 1-year limited warranty, and every board has a serial number. Support comes from the engineer who designed it.
How each stage of the board works, the fit limits, calibration and the bench test every board passes.